Electric motors and accessories

L298N motor driver - H-bridge for 2 DC motors, 5-35 V

MG90S micro servo - metal gears, 2 kg·cm, 4.8-6 V

Servo motor 12-24 V - high torque, angle or rotation, 120-380 kg

N20 gear motor - mini DC motor with metal gearbox, 3-12 V

Gimbal camera mount - 2 axes for 2x MG90 servo, up to 500 g

RF-300CA-11440 micro motor - 1.5-9 V DC, shaft Ø 2 mm

L293D motor driver IC - 4 channels, up to 36 V, 600 mA, DIP-16

Funduino SG90 servo motor - 9 g, 180°, 3,5-6 V

Wheel for N20 gear motor - 4 pieces, Ø 65 mm, 3 mm bore

RS260 electric motor - direct drive

A2212 Brushless Motor 12T - 1200 kV, 11,1 V, 30 A

SimonK 20 A Speed Controller - Brushless ESC with 5 V / 2 A BEC

MT2204 brushless motor - 2300 KV, 3S-4S LiPo, CW

MT2204 brushless motor - 2300 KV, CCW, black

Funduino MG995 Servo - 360° continuous rotation, 4.8-7.2 V, 15 kg·cm

Geared motor 3-6 V - 1:200 gear ratio, dual shaft

Servo tester - 3 modes for servo, ESC, and PWM, 4.8-6 V

Pololu DRV8825 stepper motor driver - 8.2-45 V, 2.2 A per phase

N20 Geared Motor Flip Chip - 200 rpm, 3-12 V, Shaft Ø 2 mm

N20 Getriebemotor - M3 Gewindestange 55 mm, 3-12 V, 10-1000 U/min

TT gear motor - single-shaft L motor, 3-6 V, various versions

EMAX XA2212 brushless motor - 11.1 V, 12 A, 820 and 980 KV

Linear actuator - push rod 6 V and 12 V

LANRC ESC BLHeli-S - brushless motor controller, DSHOT600, 35 A and 45 A

Stepper motor mount - die-cast aluminum, various versions

Aluminum motor mount - stepper motor and servo, NEMA17 to NEMA36

BLHeli ESC - brushless controller, 3-4S LiPo, PWM, 20-45 A

Micro linear actuator - 6 V, 128 N, 7 mm/s, 10-100 mm stroke

60GA775F gear motor - high torque, 12 V and 24 V, 100-350 rpm

Micro linear actuator - Ø 8 mm lift rod, 3-6 V, various stroke lengths

12 V Linear Actuator - 150 mm Stroke, IP54, 20-120 N

HM12 stepper motor mount NEMA 23/24 - for ball screw, various versions

TT gear motor 1:48 - metal shaft, 3-6 V DC, I- and L-shaped

EDF impeller turbine - brushless motor, Ø 27-70 mm, 3900-11000 kV

Micro linear actuator - 8 mm diameter lift rod, 3-6 V

EMAX ES08MA II micro servo - metal gears, 4.8-6 V, 2 directions of rotation

HM15 stepper motor mount - for ball screw, NEMA 23-34, various designs

TT Gear Motor with Hall Encoder - Dual Shaft, 300 rpm, 6 V and 12 V

N20 worm gear motor - 12 V, 136 rpm, dual shaft